MFlenses - デジタル時代の新しさ
MFLenses 2026

マニュアルフォーカスレンズフォーラム

修理ノート、実際のテスト写真、画像豊富な詳細アーカイブスレッドから、ヴィンテージレンズの世界を探検してください。

修理ノート、実際のテスト写真、画像豊富な詳細アーカイブスレッドから、ヴィンテージレンズの世界を探検してください。
スポットライト

フォーラムトップページのおすすめパートナー掲載。

Solvent
前のトピックへ :: 次のトピックへ  


Reply

I have only very limited experience when it comes to MF lens repair; I'm a student of the art.

But without question my most vexing problem thus far has been glued threads, to include both screw threads and lens retainer threads.

I'm curious to know what other, more experienced, practitioners are using to break this glue, this thread sealer, thus enabling lens disassembly. What are you using as a solvent???? Question

Two solvents I've seen referenced are MEK and acetone. When I think of MEK my next thought is always: cancer.

When I contemplate acetone my next thought is: good ventilation . . . . but at least not cancer.

What solvent is working for you?? Question


Reply

Solvents? I've never used a solvent to take a lens apart.


Reply

martinsmith99 氏の書き込み:
Solvents? I've never used a solvent to take a lens apart.


Martin have you ever attempted to disassemble a Hexanon or a Kiron (Vivitar Series 1). I have. Both have threads secured with sealer.

If you've not run into this impediment your lens refurbishment experiences must be quite sweet!

I dare say, absent sealer, working on these old MF lenses would be fun! Very Happy

And I write that with envy on my mind. Wink


Reply

OK

I appear to be in error regarding: MEK and: cancer.

Here is the straight story:

http://en.wikipedia.org/wiki/Methyl_ethyl_ketone

How I went wrong on that I don't know.


Reply

I used MEK for many years at work, one of its uses is to melt the surface of plastic pipe and the fittings prior to gluing, it softens the surface so the glue acts quicker when the fitting is pushed on the pipe. So there are many plastics that it will 'melt' - and it strips a lot of paints as well. It's nasty stuff, and you certainly wouldn't want any excess on lens parts, especially coated optics.

If it's tight screws that won't come apart, then I sometimes touch an already hot pointed and clean tip of a soldering iron on the screw head - briefly. Just long enough to get some heat in the screw and cause a bit of expansion, but not enough to melt any plastic components. It's not as drastic as it sounds, and often better than splashing solvents about,


Reply

Lloydy 氏の書き込み:
I used MEK for many years at work, one of its uses is to melt the surface of plastic pipe and the fittings prior to gluing, it softens the surface so the glue acts quicker when the fitting is pushed on the pipe. So there are many plastics that it will 'melt' - and it strips a lot of paints as well. It's nasty stuff, and you certainly wouldn't want any excess on lens parts, especially coated optics.

If it's tight screws that won't come apart, then I sometimes touch an already hot pointed and clean tip of a soldering iron on the screw head - briefly. Just long enough to get some heat in the screw and cause a bit of expansion, but not enough to melt any plastic components. It's not as drastic as it sounds, and often better than splashing solvents about,


Appreciate the post. Don't really disagree. All these solvents frighten me. Don't like 'em. Can't live without 'em, though.

The MEK citation is not based on my own experience. I lifted (stole) the reference from the Vivitar manual for disassembly of their Series 1 70-210mm. The manual URL was posted (albeit indirectly) by another member (credit to Nikonshooter) of this forum on the main board thread where we discussed that lens. Here is an entry point:

http://www.boggys.co.uk/page40.html

I think (working from memory) I came across the MEK reference in the publication entitled "SPT Repair Notes".

This thread is intended to help me learn about solvents being used by others. But that manual was interesting. It pointed out that, rather than tightening screws completely, that Kiron (Vivitar Series 1) has certain screws left a bit slack intentionally, then glued. They don't want the screws tight because doing so can disrupt/distort the optics of the lens.

That is not the kind of thing I'm smart enough to divine on my own. And it highlights the importance of solvents, for certain lenses (though surely not all lenses), both at disassembly and at reassembly time.


Reply

If a strong solvent becomes the best option to dissolve the screw locking stuff, then I would use a fine syringe such as a medical one. I've got a couple and use one for light oil and one for solvents. I got them off a friendly vet and bluntened the ends.