MFlenses - デジタル時代の新しさ
MFLenses 2026

マニュアルフォーカスレンズフォーラム

修理ノート、実際のテスト写真、画像豊富な詳細アーカイブスレッドから、ヴィンテージレンズの世界を探検してください。

修理ノート、実際のテスト写真、画像豊富な詳細アーカイブスレッドから、ヴィンテージレンズの世界を探検してください。
スポットライト

フォーラムトップページのおすすめパートナー掲載。

Making pinholes
前のトピックへ :: 次のトピックへ  


Reply

Hi does anyone know how to make a really nice pinhole without jagged edges, or can I buy a piece if perforated material with a purpose made pinhole in it??


Reply

Apparently the way to do it is not to poke the pin all the way through, but to make an indent, then rub the nipple you have formed on emery paper until you get a small hole.


Reply

I've also heard spinning a needle into the metal would help.


Reply

The pro ones are built by a laser punch. Difficult to do it at home Wink


Reply

This guy used a 3W 450nm laser to cut a hole through cardboard.

Whether it would work for metal and the beam is sufficiently thin I don't know. Smile





Reply

Drill press with a drill press vise. Or some clamps instead of vise.
Fix a needle in the chuck. An insulin syringe needle.
That`s the way I`d do it.


Reply

I bought two pinholes from eBay that were laser drilled and perfectly circular. They both diffract more and are softer than ones I made pushing a pin through tin foil and aluminum can bodies. In fact, one one of the latter I managed a pinhole that's so sharp it captures tree leaf details at 40 feet. I'm of the might right now that, with pinholes, it's very fast to reach a point of diminished returns.


Reply

Thanks for your help there, Thats interesting, David that a punched pinhole of the type I am trying to avoid will give better results than a bought one. I'll try it. Ian's suggestion of sanding down a nipple might work. On tin foil I mean.


Reply

Clamp the plate you want to drill between two other thicker plates and clamp them very firmly as close to where you want to drill as possible, use heavy washers to get the plates as tight as you can and drill through the washer hole, then drill the hole with a model makers drill bit in a dremel or with a spiral drill - http://www2.westfalia.net/shops/tools/hand_tools/gimlets/an_assortment_of_gimlets/411275-mini_hand_drill.htm
which you can get from Hobbycraft for a few pounds.
The other alternative is to glue the sheet you want the hole in between two other sheets with a glue that will melt with heat, but it needs to be a thin layer.
The idea is to prevent burrs by not allowing any space for them to form on the plate you need, so it must be a thin layer of glue or very firmly clamped.


Reply

Let us know how you get on Phil as I have been thinking of trying pinhole. I have loads of paper and x-ray film, both are very slow, I thought of going to see my mate who owns a carpet shop and getting a lump of the large diameter cardboard tube from the middle of the carpet rolls to make a cylindrical pinhole camera that takes really big negatives, such as 12x18 inches.


Reply

Found at Wikipedia:

Selection of pinhole size:

Within limits, a smaller pinhole (with a thinner surface that the hole goes through) will result in sharper image resolution because the projected circle of confusion at the image plane is practically the same size as the pinhole. An extremely small hole, however, can produce significant diffraction effects and a less clear image due to the wave properties of light.[11] Additionally, vignetting occurs as the diameter of the hole approaches the thickness of the material in which it is punched, because the sides of the hole obstruct the light entering at anything other than 90 degrees.

The best pinhole is perfectly round (since irregularities cause higher-order diffraction effects), and in an extremely thin piece of material. Industrially produced pinholes benefit from laser etching, but a hobbyist can still produce pinholes of sufficiently high quality for photographic work.

One method is to start with a sheet of brass shim or metal reclaimed from an aluminium drinks can or tin foil/aluminum foil, use fine sand paper to reduce the thickness of the centre of the material to the minimum, before carefully creating a pinhole with a suitably sized needle.

A method of calculating the optimal pinhole diameter was first attempted by Jozef Petzval. The crispest image is obtained using a pinhole size determined by the formula:

d=\sqrt{2f\lambda}

where d is pinhole diameter, f is focal length (distance from pinhole to image plane) and λ is the wavelength of light.

For standard black-and-white film, a wavelength of light corresponding to yellow-green (550 nm) should yield optimum results. For a pinhole-to-film distance of 1 inch (25 mm), this works out to a pinhole 0.17 mm in diameter.[13] For 5 cm, the appropriate diameter is 0.23 mm.

The depth of field is basically infinite, but this does not mean that no optical blurring occurs. The infinite depth of field means that image blur depends not on object distance, but on other factors, such as the distance from the aperture to the film plane, the aperture size, and the wavelength(s) of the light source.


Reply

On my Photo Tinker Directory are some links with pinhole building instructions:

Here two of them:

German, but the way sounds good, electric pinhole burning with a needle and capacitor, and 12V voltage supply:
http://www.jochen-reincke.de/lochkam/loecher.htm

http://web.archive.org/web/20031006023328/http://www.pinhole.com/resources/articles/poke.php

For a bigger ~2mm hole for an iris I tested the sun focused with a lens. For pinholes CCTV lenses or such with short focal length could probably work for pinholes. I think focal lengths ~20mm and shorter.
I worked handholding the lens, that was bad, but with fixed lens and probably a grey filter one could aim and focus, a black paper in front of the lens could be the shutter for the "burning exposure".
Don´t look through the lens!


Reply

http://www.bbc.co.uk/news/in-pictures-22150973

good stuff. Cool


Reply

Thanks for this, I had wondered if you'd get diffraction from too small a pinhole. The coke can and the sanded-down nipple sounds like a good combination