MFlenses - デジタル時代の新しさ
MFLenses 2026

マニュアルフォーカスレンズフォーラム

修理ノート、実際のテスト写真、画像豊富な詳細アーカイブスレッドから、ヴィンテージレンズの世界を探検してください。

修理ノート、実際のテスト写真、画像豊富な詳細アーカイブスレッドから、ヴィンテージレンズの世界を探検してください。
スポットライト

フォーラムトップページのおすすめパートナー掲載。

Loading bulk film
前のトピックへ :: 次のトピックへ  


Reply

A lot of film manufacturer's still provide 35 mm film in 100' "bulk" rolls of film and there are re-usable 35 mm film cassettes too.

Using a bulk film loader similar to the WATSON can save a lot of money over a year's shooting. I also like to be able to load short rolls, 6 to 12 exposures for testing cameras. Here is a description of my method. This process eliminates the totally exposed film at the spool end of the film. I do this in the darkroom, but I don't see any reason a changing bag would not work. Just make sure the bulk roll does not get exposed.


Bulk loader with film installed


I use the blue painters tape available nearly every where here in the USA. Three quarters on an inch wide, I cut it lengthwise to approximately 3/8" wide. Just easier for me to use.


Loader in full light with GATE CLOSED


Cartridge spool taped on. The tape must wrap around the spool stuck to both sides of the film.


Cartridge installed, notice the short length of the film between the cartridge and gate.


I put an empty cartridge in the actual loading position for reference.

Now our imagination has to get going. Turn off the light, open the gate then move the assembled cartridge into the loading position. Make sure the perforations are positioned on the cogs so that the counter works. If you leave the gate shut, the film might get scratched. Shut the door on the loader. Then turn the light on.

Note: The gate may need to be repositioned to close the door. Just make sure the door is completely closed and the gate open.

Turn the crank to load the desired number of exposures into the cartridge. I load two or three extra to allow of the 'leader' on the roll of film. Then shut the gate. Now the bulk roll is protected from light and the door can be opened.


Cut the film between the gate and cartridge. Remove the roll of film.


Cut the leader shape on the end of the film.

Wow, it is a lot easier to do than describe the process. Please feel free to offer corrections and suggestions.

Phil


Reply

Thanks for your time to show and explain the process,I have not yet ventured into this area of loading your own film. Cool


Reply

Thanks...... and B/W films keep (well I suppose there could be some exceptions ?) as now and again use my bulk FP4 I loaded into my Watson over 20 years ago.


Reply

Phil,

Very useful, thanks for sharing,

Cheers,

Renato


Reply

Nice tutorial. I eventually bought one of these loaders, a Watson.

Before that I used a yardstick with pins hammered into it at the start then the 12, 20 and 36 exposure distances stuck vertically on the wall. I hooked a perforation over the appropriate pin and unrolled the film down to the start pin. I hooked it over the start pin then cut it from the roll. I then stuck the end to the spool and closed the cassette. Keeping the film taut I spooled it into the cassette. I didnt handle the film at all doing this.

Once in a while the curl would be too strong and it would spring off. I'd be feeling around in the dark for the film on the floor. Even then though I dont recall ruining any films.

The pins I used were those large headed type that come with new shirts.

Do it in the dark.


最終編集: philslizzy、日 12月 14, 2014 9:33 am、計 1 回


Reply

Always fun dropping things in total darkness. The loader makes it a lot easier.

Phil


Reply

PWhite214 氏の書き込み:
Always fun dropping things in total darkness. The loader makes it a lot easier.

Phil


So true!! I dont use so much b&w these days