| 前のトピックへ :: 次のトピックへ |
| 作成者 |
メッセージ |
cbass
 登録日: 2019年7月27日 投稿: 457
|
 投稿日時: 月 2月 07, 2022 6:19 am 件名: Front Element Contamination |
|
 投稿日時: 月 2月 07, 2022 6:19 am 件名: Front Element Contamination |
|
|
cbass wrote:
This is another lens I have picked up. This appears to be on the back of the front element. I have taken out the front element and cleaned with alcohol and it does not seem to have made any difference.
What is this? Is this coating damage from Fungus that has been previously cleaned or something else? It's very difficult to see but looks like a hazy contamination.
Better clue. Focus is a big different but in roughly the same location. It no longer looks hazy. Instead a hair like structure appears.
 |
|
| トップへ戻る |
|
 |
RokkorDoctor
 登録日: 2021年11月27日 投稿: 1562 所在地: Kent, UK
Expire: 2025-05-01
|
 投稿日時: 月 2月 07, 2022 5:58 pm 件名: |
|
 投稿日時: 月 2月 07, 2022 5:58 pm 件名: |
|
|
RokkorDoctor wrote:
As to the second image; I suspect that is in fact the back-lit reflection of your own hair you are looking at, but I could be wrong
As to the original problem; I have seen this before.
First try some other solvents as well; water (distilled if you have it to hand), and acetone. If that doesn't remove it it is likely permanent damage. I have several optics that have that type of damage. Could be coating damage, but usually it is chemical damage to the glass.
I'm sure on this forum there are some glass experts that can explain better, but as far as I understand, long term exposure to condensation can be one cause of this; Alkali ions diffuse from the glass into small water droplets that have condensed on the surface. The alkaline solutions then erode the silica gel layer of the polished surface. After the condensation evaporates silicon ions and alkali are deposited on the glass surface leaving a hazy film that cannot be removed by wiping (references: H.H. Karow, "Fabrication Methods For Precision Optics",Wiley-Interscience, 2004 & T.S. Izumitani, "Optical Glass", UCRL-Trans-12065, LLNL, 1985 & Hoya Corporation on the phenomenon of "dimming", Japan).
This type of damage can only be removed by re-polishing (and subsequent re-coating).
Hence it is possible the lens was cleaned before, but reassembled under warm & high RH conditions and then sealed & brought into a low temperature environment. You would then get internal condensation along the wipe marks left on the glass surface, with possible damage described as per the above.
But, it could also be something else. _________________ Mark
SONY A7S, A7RII + dust-sealed modded Novoflex/Fotodiox/Rayqual MD-NEX adapters
Minolta SR-1, SRT-101/303, XD7/XD11, XGM, X700
Bronica SQAi
Ricoh GX100
Minolta majority of all Rokkor SR/AR/MC/MD models made
Sigma 14mm/3.5 for SR mount
Tamron SP 60B 300mm/2.8 (Adaptall)
Samyang T-S 24mm/3.5 (Nikon mount, DIY converted to SR mount)
Schneider-Kreuznach PC-Super-Angulon 28mm/2.8 (SR mount)
Bronica PS 35/40/50/65/80/110/135/150/180/200/250mm |
|
| トップへ戻る |
|
 |
cbass
 登録日: 2019年7月27日 投稿: 457
|
 投稿日時: 火 2月 08, 2022 12:52 am 件名: |
|
 投稿日時: 火 2月 08, 2022 12:52 am 件名: |
|
|
cbass wrote:
I think you are right. I was surprised to see that hair like structure as I could not see anything like it when I shined a light through the lens. Now I am surprised by my own stupidity. That is a reflection of my own hair. How shameful.
When you say distilled water and acetone do you mean Just distilled water and just acetone or do you mean mix water and acetone? If so, then in what ratio? I do not have any background in cleaning lenses so this is not clear to me.
Anything else I should try?
Dish soap and water?
Hydrogen peroxide? |
|
| トップへ戻る |
|
 |
RokkorDoctor
 登録日: 2021年11月27日 投稿: 1562 所在地: Kent, UK
Expire: 2025-05-01
|
 投稿日時: 火 2月 08, 2022 10:36 am 件名: |
|
 投稿日時: 火 2月 08, 2022 10:36 am 件名: |
|
|
RokkorDoctor wrote:
I mean separately.
Some contamination is water soluble, others are soluble in either alcohol or acetone.
You can also get reactions happening where one solvent reacts with the contaminants to leave a residue that is then soluble in another solvent.
On stubborn contamination I usually try a few different solvents in succession, and I usually finish with acetone.
Commercially (in the manufacturing of optics) they use some far more aggressive solvents but they are not usually available to the general public, for good reason. Some of those are due to be phased out anyway because of tightening environmental controls.
If you can get the elements out then I have sometimes found a liquid hand soap to do wonders as well. Just try get one for sensitive hands without perfume. _________________ Mark
SONY A7S, A7RII + dust-sealed modded Novoflex/Fotodiox/Rayqual MD-NEX adapters
Minolta SR-1, SRT-101/303, XD7/XD11, XGM, X700
Bronica SQAi
Ricoh GX100
Minolta majority of all Rokkor SR/AR/MC/MD models made
Sigma 14mm/3.5 for SR mount
Tamron SP 60B 300mm/2.8 (Adaptall)
Samyang T-S 24mm/3.5 (Nikon mount, DIY converted to SR mount)
Schneider-Kreuznach PC-Super-Angulon 28mm/2.8 (SR mount)
Bronica PS 35/40/50/65/80/110/135/150/180/200/250mm |
|
| トップへ戻る |
|
 |
cbass
 登録日: 2019年7月27日 投稿: 457
|
 投稿日時: 火 2月 08, 2022 9:43 pm 件名: |
|
 投稿日時: 火 2月 08, 2022 9:43 pm 件名: |
|
|
cbass wrote:
I think I will try my luck again.
I can use pure acetone or does it need to be diluted?
I also have a product called goof off. Is that safe on optics? |
|
| トップへ戻る |
|
 |
visualopsins
 登録日: 2009年3月5日 投稿: 11698 所在地: California
Expire: 2027-07-11
|
 投稿日時: 火 2月 08, 2022 9:56 pm 件名: |
|
 投稿日時: 火 2月 08, 2022 9:56 pm 件名: |
|
|
visualopsins wrote:
| cbass 氏の書き込み: |
I think I will try my luck again.
I can use pure acetone or does it need to be diluted?
I also have a product called goof off. Is that safe on optics? |
Depends -- old Goof Off contains Xylene; new Goof Off is made with acetone. https://www.popularwoodworking.com/woodworking-blogs/goof-off-has-changed/
Bio-Friendly Alternatives for Xylene – Carrot oil, Olive oil, Pine oil, Rose oil https://www.ncbi.nlm.nih.gov/pmc/articles/PMC4668515/
https://blog.4evaseal.com/dos-and-donts-when-cleaning-surfaces-with-solvent-
https://en.wikipedia.org/wiki/Xylene
| 引用: |
The main effect of inhaling xylene vapor is depression of the central nervous system (CNS), with symptoms such as headache, dizziness, nausea and vomiting. At an exposure of 100 ppm, one may experience nausea or a headache. At an exposure between 200 and 500 ppm, symptoms can include feeling "high", dizziness, weakness, irritability, vomiting, and slowed reaction time.[21][22]
The side effects of exposure to low concentrations of xylene (< 200 ppm) are reversible and do not cause permanent damage. Long-term exposure may lead to headaches, irritability, depression, insomnia, agitation, extreme tiredness, tremors, hearing loss, impaired concentration and short-term memory loss.[23][clarification needed] A condition called chronic solvent-induced encephalopathy, commonly known as "organic solvent syndrome" has been associated with xylene exposure. There is very little information available that isolates xylene from other solvent exposures in the examination of these effects.[21]
Hearing disorders have been also linked to xylene exposure, both from studies with experimental animals,[24][25] as well as clinical studies.[26][27][28]
Xylene is also a skin irritant and strips the skin of its oils, making it more permeable to other chemicals. The use of impervious gloves and masks, along with respirators where appropriate, is recommended to avoid occupational health issues from xylene exposure.[21] |
_________________ ☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮ like attracts like! ☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮
Cameras: Sony ILCE-7RM2, Spotmatics II, F, and ESII, Nikon P4
Lenses:
M42 Asahi Optical Co., Takumar 1:4 f=35mm, 1:2 f=58mm (Sonnar), 1:2.4 f=58mm (Heliar), 1:2.2 f=55mm (Gaussian), 1:2.8 f=105mm (Model I), 1:2.8/105 (Model II), 1:5.6/200, Tele-Takumar 1:5.6/200, 1:6.3/300, Macro-Takumar 1:4/50, Auto-Takumar 1:2.3 f=35, 1:1.8 f=55mm, 1:2.2 f=55mm, Super-TAKUMAR 1:3.5/28 (fat), 1:2/35 (Fat), 1:1.4/50 (8-element), Super-Multi-Coated Fisheye-TAKUMAR 1:4/17, Super-Multi-Coated TAKUMAR 1:4.5/20, 1:3.5/24, 1:3.5/28, 1:2/35, 1:3.5/35, 1:1.8/85, 1:1.9/85 1:2.8/105, 1:3.5/135, 1:2.5/135 (II), 1:4/150, 1:4/200, 1:4/300, 1:4.5/500, Super-Multi-Coated Macro-TAKUMAR 1:4/50, 1:4/100, Super-Multi-Coated Bellows-TAKUMAR 1:4/100, SMC TAKUMAR 1:1.4/50, 1:1.8/55
M42 Carl Zeiss Jena Flektogon 2.4/35
Contax Carl Zeiss Vario-Sonnar T* 28-70mm F3.5-4.5
Pentax K-mount SMC PENTAX-A ZOOM 1:3.5 35~105mm, SMC PENTAX ZOOM 1:4 45~125mm
Nikon Micro-NIKKOR-P-C Auto 1:3.5 f=55mm, NIKKOR-P Auto 105mm f/2.5 Pre-AI (Sonnar), Micro-NIKKOR 105mm 1:4 AI, NIKKOR AI-S 35-135mm f/3,5-4,5
Solinon 1:5.6/18 ASPH.
Tamron SP 17mm f/3.5 (51B), Tamron SP 17mm f/3.5 (151B), SP 500mm f/8 (55BB), SP 70-210mm f/3.5 (19AH)
Vivitar 100mm 1:2.8 MC 1:1 Macro Telephoto (Kiron)
|
|
| トップへ戻る |
|
 |
RokkorDoctor
 登録日: 2021年11月27日 投稿: 1562 所在地: Kent, UK
Expire: 2025-05-01
|
 投稿日時: 土 2月 12, 2022 10:18 am 件名: |
|
 投稿日時: 土 2月 12, 2022 10:18 am 件名: |
|
|
RokkorDoctor wrote:
| cbass 氏の書き込み: |
I think I will try my luck again.
I can use pure acetone or does it need to be diluted?
I also have a product called goof off. Is that safe on optics? |
Use pure acetone.
Never heard of goof off, but I see visualopsins already replied. Personally, I would stay clear of it and stick to the known solvents used in the optics manufacturing industry. _________________ Mark
SONY A7S, A7RII + dust-sealed modded Novoflex/Fotodiox/Rayqual MD-NEX adapters
Minolta SR-1, SRT-101/303, XD7/XD11, XGM, X700
Bronica SQAi
Ricoh GX100
Minolta majority of all Rokkor SR/AR/MC/MD models made
Sigma 14mm/3.5 for SR mount
Tamron SP 60B 300mm/2.8 (Adaptall)
Samyang T-S 24mm/3.5 (Nikon mount, DIY converted to SR mount)
Schneider-Kreuznach PC-Super-Angulon 28mm/2.8 (SR mount)
Bronica PS 35/40/50/65/80/110/135/150/180/200/250mm |
|
| トップへ戻る |
|
 |
|
|
|
このフォーラムでは新しいトピックを投稿できません このフォーラムではトピックに返信できません このフォーラムでは自分の投稿を編集できません このフォーラムでは自分の投稿を削除できません このフォーラムでは投票に参加できません
|