MFlenses - デジタル時代の新しさ
MFLenses 2026

マニュアルフォーカスレンズフォーラム

修理ノート、実際のテスト写真、画像豊富な詳細アーカイブスレッドから、ヴィンテージレンズの世界を探検してください。

修理ノート、実際のテスト写真、画像豊富な詳細アーカイブスレッドから、ヴィンテージレンズの世界を探検してください。
スポットライト

フォーラムトップページのおすすめパートナー掲載。

Problem with unscrewing the lens ring on the Canon FD 35-70
前のトピックへ :: 次のトピックへ  


Reply

I have a Canon FD 35-70 SSC lens on my table. The problem is that the zoom mechanism rollers are damaged and one lens is dirty. Specifically, it is the last lens of the front optical block. There is fogging inside, and I cannot unscrew the rear ring (applying a minimal amount of acetone to the thread does not help). The manufacturer probably used some kind of “glue” to prevent spontaneous unscrewing. After many years, this agent has glued hard the thread, which makes it difficult to unscrew. At least that's what I suspect.

Can you suggest an effective way to unscrew this ring? I don't want to ruin this fine lens. For now, I consider heating it in the oven to be a last resort.

I am attaching photos of the entire group (without the front lens, which is removed separately, first).

https://www.photrio.com/forum/attachments/dscf6684-jpg.413976/

https://www.photrio.com/forum/attachments/dscf6694-jpg.413977/


Reply

Welcome miki11

Other folks will be along shortly with real answers; probably using a drop or two of some sort of solvent on the ring, being especially careful to avoid getting any on the edges of cemented lens elements.


Reply

visualopsins 氏の書き込み:
Welcome miki11

Other folks will be along shortly with real answers; probably using a drop or two of some sort of solvent on the ring, being especially careful to avoid getting any on the edges of cemented lens elements.


There are no cemented lenses in the entire FD 2.8-3.5/35-70mm SSC; therefore I would try to immerse the block for some time in a solvent like acetone. Sometimes it takes a few minutes (or even half an hour) to loosen the elements. I'm pretty sute that this should work - unless the element was factory sealed with an epoxy resin: That would require careful heating indeed.

S


Reply

stevemark 氏の書き込み:
visualopsins 氏の書き込み:
Welcome miki11

Other folks will be along shortly with real answers; probably using a drop or two of some sort of solvent on the ring, being especially careful to avoid getting any on the edges of cemented lens elements.


There are no cemented lenses in the entire FD 2.8-3.5/35-70mm SSC; therefore I would try to immerse the block for some time in a solvent like acetone. Sometimes it takes a few minutes (or even half an hour) to loosen the elements. I'm pretty sute that this should work - unless the element was factory sealed with an epoxy resin: That would require careful heating indeed.

S


Yes, this zoom lens has 10 lenses in 10 groups. The front block contains 5 separate lenses, and the one that is dirty is the fifth one (counting from the front).

After two days of gently soaking the thread with acetone, I finally managed to unscrew the ring last night. I tried to clean it (with hydrogen peroxide, IPA - 99% isopropyl alcohol, Zeiss optics cleaner), but unfortunately I couldn't remove the artifact. I immersed the entire element in IPA for 10 hours, but that didn't help either. Here is the result after today's inspection.

https://www.photrio.com/forum/attachments/dscf6695-jpg.414018/

What agent can help me remove this “haze” without risking damage to the coatings?


Reply

miki11 氏の書き込み:

After two days of gently soaking the thread with acetone, I finally managed to unscrew the ring last night. I tried to clean it (with hydrogen peroxide, IPA - 99% isopropyl alcohol, Zeiss optics cleaner), but unfortunately I couldn't remove the artifact. I immersed the entire element in IPA for 10 hours, but that didn't help either. Here is the result after today's inspection.

https://www.photrio.com/forum/attachments/dscf6695-jpg.414018/

What agent can help me remove this “haze” without risking damage to the coatings?


I have encountered this kind of damage on two lenses - on the front lenses of a Mamiya Sekor C 4/210mm and the front lenses of a Pettri 4/200mm. I suspect the surface is etched by some aggessive chemicals either from the lens barrel or from the surroundings. Probably the only way to improve the situation would be re-polishing the lens surface (e. g. with cerium oxide powder).

S


Reply

Try pure soap and water.


Reply

visualopsins 氏の書き込み:
Try pure soap and water.


Polishing - or just washing?

I case of the two lenses I mentioned above (Mamiya Sekor C 4/210 and Petri 4/200) the lens surfaces clearly are damaged; simply washing didn't result in any improvement.

Many years ago Zeiss Oberkochen seems to have promoted using cigarette ash for polishing:
https://richardhaw.com/2020/12/13/repair-polishing-glass-part-1/

Not sure whether that's a urban legend, though ...

I haven't tried, but since I have some smoker friends I should aks them for some ash ...

S