| 前のトピックへ :: 次のトピックへ |
| 作成者 |
メッセージ |
oldschool
登録日: 2016年10月18日 投稿: 17
|
 投稿日時: 火 2月 28, 2017 2:27 pm 件名: Stuck aperture blades on Flektagon 35mm 2.4 |
|
 投稿日時: 火 2月 28, 2017 2:27 pm 件名: Stuck aperture blades on Flektagon 35mm 2.4 |
|
|
oldschool wrote:
Can anyone help me free up the aperture blades on the Carl Zeiss Flektagon 35mm f/2.4?
The Aperture is mainly stuck open. In A mode the rear pin has resistance and when pressed the blades do not move. In M mode the pin has no resistance and does nothing.
The aperture ring does nothing in either mode.
I have removed the rear case and I can get the blades to open and close by simulating M mode to release the rocker spring tension and then pushing the lever underneath to move the blades.
Anyone have any experience of this? Appears to be a common complaint but i cant see any guide to fixing.
Thanks |
|
| トップへ戻る |
|
 |
oldschool
登録日: 2016年10月18日 投稿: 17
|
 投稿日時: 火 2月 28, 2017 4:33 pm 件名: |
|
 投稿日時: 火 2月 28, 2017 4:33 pm 件名: |
|
|
oldschool wrote:
OK I worked it out and all now works perfectly.
1. dissasemble lens as here - http://www.kolumbus.fi/uusilehto/img/lenses/zeiss/disass/slides/lens.html
2. Follow step 9 in the cleaning guide here - http://www.aprd31.dsl.pipex.com/articles/czj135svc/
3. I should probably loosen off and realign focussing barrel but I didnt. |
|
| トップへ戻る |
|
 |
SonicScot
 登録日: 2011年12月1日 投稿: 2697 所在地: Scottish Highlands
|
 投稿日時: 金 3月 03, 2017 12:26 am 件名: |
|
 投稿日時: 金 3月 03, 2017 12:26 am 件名: |
|
|
SonicScot wrote:
I would suggest that you always keep the blades closed when you're not using it. I've done that ever since fixing mine, it hasn't happened since. _________________ Gary
Currently active gear....
Sony a7
E-M1 Mkll
Rubinar 1000/10 + 2x matched extender
Tamron 500/8 55BB
Sigma 100-300/4
Vivitar Series 1.... 200/3, 70-210/3.5 (V1 by Kiron), 135/2.3, 105/2.5 macro, 90/2.5 macro (Bokina), 90-180/4.5 Flat Field Macro, 28-90mm f/2.8-3.5
Carl Zeiss.... 180/2.8, 135/3.5, 85/1.4, 35/2.4 Flektagon, 21/2.8 Distagon
Nikon.... 55/3.5 micro, 50/1.2
Elicar 90/2.5 V-HQ Macro
Zhongyi Speedmaster 85/1.2
Jupiter-9 85/2
Helios.... 58/2 44-3
Hartblei 45/3.5 Super-Rotator TS-PC
Zenitar 16/2.8 fisheye
Samyang 8/3.5 fisheye
Nodal Ninja 4, Neewer leveling tripod base
Flickr http://www.flickr.com/photos/gazsus/ Website http://garianphotography.co.uk/ |
|
| トップへ戻る |
|
 |
Excalibur
 登録日: 2009年7月19日 投稿: 5018 所在地: UK
Expire: 2014-04-21
|
 投稿日時: 金 3月 03, 2017 11:54 am 件名: |
|
 投稿日時: 金 3月 03, 2017 11:54 am 件名: |
|
|
Excalibur wrote:
Thanks for the link... my CZJ 135mm Sonnar has a peculiar problem for focussing in that I've taken the back off and re-assembled and it would start from infinity, but when focussing back to min distance, it then only goes back to 6ft (hits a stop).....so I have to study the instructions on how to set it i.e. min distance to infinity. _________________ Canon A1, AV1, T70 & T90, EOS 300 and EOS300v, Chinon CE and CP-7M. Contax 139, Fuji STX-2, Konica Autoreflex TC, FS-1, FT-1, Minolta X-700, X-300, XD-11, SRT101b, Nikon EM, FM, F4, F90X, Olympus OM2, Pentax S3, Spotmatic, Pentax ME super, Praktica TL 5B, & BC1, , Ricoh KR10super, Yashica T5D, Bronica Etrs, Mamiya RB67 pro AND drum roll:- a Sony Nex 3
.........past gear Tele Rolleiflex and Rollei SL66.
Many lenses from good to excellent. |
|
| トップへ戻る |
|
 |
hasan
 登録日: 2007年3月12日 投稿: 313
|
 投稿日時: 金 3月 03, 2017 12:04 pm 件名: |
|
 投稿日時: 金 3月 03, 2017 12:04 pm 件名: |
|
|
hasan wrote:
| Excalibur 氏の書き込み: |
| Thanks for the link... my CZJ 135mm Sonnar has a peculiar problem for focussing in that I've taken the back off and re-assembled and it would start from infinity, but when focussing back to min distance, it then only goes back to 6ft (hits a stop).....so I have to study the instructions on how to set it i.e. min distance to infinity. |
Hi, have you already seen this thread?
http://forum.mflenses.com/viewtopic.php?t=14453
and here
http://www.aprd31.dsl.pipex.com/articles/czj135svc/
kind regards
hasan |
|
| トップへ戻る |
|
 |
Excalibur
 登録日: 2009年7月19日 投稿: 5018 所在地: UK
Expire: 2014-04-21
|
 投稿日時: 金 3月 03, 2017 9:16 pm 件名: |
|
 投稿日時: 金 3月 03, 2017 9:16 pm 件名: |
|
|
Excalibur wrote:
| hasan 氏の書き込み: |
| Excalibur 氏の書き込み: |
| Thanks for the link... my CZJ 135mm Sonnar has a peculiar problem for focussing in that I've taken the back off and re-assembled and it would start from infinity, but when focussing back to min distance, it then only goes back to 6ft (hits a stop).....so I have to study the instructions on how to set it i.e. min distance to infinity. |
Hi, have you already seen this thread?
http://forum.mflenses.com/viewtopic.php?t=14453
and here
http://www.aprd31.dsl.pipex.com/articles/czj135svc/
kind regards
hasan |
Thanks..what is strange\coincidence is I bought two 135mm CZJ Sonnars years ago (seperate times in a MTL3 kit with Flektogon), but when I picked out a Sonnar to use on a shoot over the years, the hand of god (football fans will know) always guided me to the working one to use until recently and then found the other Sonnar had a problem i.e. won't go over 6ft.  _________________ Canon A1, AV1, T70 & T90, EOS 300 and EOS300v, Chinon CE and CP-7M. Contax 139, Fuji STX-2, Konica Autoreflex TC, FS-1, FT-1, Minolta X-700, X-300, XD-11, SRT101b, Nikon EM, FM, F4, F90X, Olympus OM2, Pentax S3, Spotmatic, Pentax ME super, Praktica TL 5B, & BC1, , Ricoh KR10super, Yashica T5D, Bronica Etrs, Mamiya RB67 pro AND drum roll:- a Sony Nex 3
.........past gear Tele Rolleiflex and Rollei SL66.
Many lenses from good to excellent. |
|
| トップへ戻る |
|
 |
hasan
 登録日: 2007年3月12日 投稿: 313
|
 投稿日時: 金 3月 03, 2017 9:59 pm 件名: |
|
 投稿日時: 金 3月 03, 2017 9:59 pm 件名: |
|
|
hasan wrote:
In http://www.aprd31.dsl.pipex.com/articles/czj135svc/
following may be the hint you are looking for:
..Set the mode to (A). The aperture ring should not function, if it does then you mis-aligned the mode selection lever when putting the case back on. Set the mode to (M). The aperture ring should stop the lens up and down freely. Test the focus. This is where you find out whether you got the infinity adjustment correct. You should be able to focus back to infinity and down to just below 1m, hitting a hard stop at each limit. If you either can't reach infinity, or the focus barrel screws all the way out past 1m then your infinity adjustment is wrong and you need to go back and set it again paying particular attention to the configuration in figure 13. The first time I took this lens apart I wasn't aware of the importance of the adjustment screw and had to reset it by trial and error. It took ages.." |
|
| トップへ戻る |
|
 |
hasan
 登録日: 2007年3月12日 投稿: 313
|
 投稿日時: 金 3月 03, 2017 10:03 pm 件名: |
|
 投稿日時: 金 3月 03, 2017 10:03 pm 件名: |
|
|
hasan wrote:
@oldschool
sorry for hijacking your thread.
congrats, by the way! |
|
| トップへ戻る |
|
 |
proplus
登録日: 2018年9月20日 投稿: 3
|
 投稿日時: 月 10月 12, 2020 8:06 am 件名: |
|
 投稿日時: 月 10月 12, 2020 8:06 am 件名: |
|
|
proplus wrote:
I know this is an old thread, but do you happen to recall which bits needs cleaning? The website for your 'step 9' no longer loads
The aperture on mine is stuck wide open, taking the lens apart and can close the aperture (with a combination of if a manually push a tiny notch), I've cleaned the blades and all around it. |
|
| トップへ戻る |
|
 |
Gonzoo
 登録日: 2010年3月29日 投稿: 231
|
 投稿日時: 月 10月 12, 2020 7:17 pm 件名: |
|
 投稿日時: 月 10月 12, 2020 7:17 pm 件名: |
|
|
Gonzoo wrote:
If the blades are clean you should be able to operate the aperture - if it is assembled correctly. Can you post a picture of the aperture? _________________ Canon 5d | Exa 500 | Pentacon Six + too much lenses  |
|
| トップへ戻る |
|
 |
proplus
登録日: 2018年9月20日 投稿: 3
|
 投稿日時: 火 10月 13, 2020 7:54 am 件名: |
|
 投稿日時: 火 10月 13, 2020 7:54 am 件名: |
|
|
proplus wrote:
| Gonzoo 氏の書き込み: |
| If the blades are clean you should be able to operate the aperture - if it is assembled correctly. Can you post a picture of the aperture? |
I made a quick video of this about a year ago: https://www.youtube.com/watch?v=7v1uBKwbAMI
Skip to around 2:58, the video angle doesn't show it very well but that is when my thumb is pushing back on the rocker switch. You can see I can close the blades via a notch accessed with the screwdriver deep within the aperture mechanism. From then the aperture arm can open the blades, but turning the arm the other way does not close down the blades. |
|
| トップへ戻る |
|
 |
Gonzoo
 登録日: 2010年3月29日 投稿: 231
|
 投稿日時: 火 10月 13, 2020 11:58 am 件名: |
|
 投稿日時: 火 10月 13, 2020 11:58 am 件名: |
|
|
Gonzoo wrote:
First I thought that the spring attached to the aperture lever that pulls back the aperture blades is missing. But I saw it still attached ealier in the video. Maybe there is something wrong with the spring tension - it might be to weak to pull the aperture shut. Also there is still some oil on the blades.
My advice would be to disassemble the aperture completly to get to the bottom if the problem. This way you can get it cleaned properly. Reassembly might be a bit frustating though
To get an idea of the process have a look towards the end of this page: http://forum.mflenses.com/cleaning-aperture-czj-tessar-105mm-f3-5-t75857,highlight,%2Btessar.html
The lens is different but the mechanism is basicly the same. _________________ Canon 5d | Exa 500 | Pentacon Six + too much lenses  |
|
| トップへ戻る |
|
 |
proplus
登録日: 2018年9月20日 投稿: 3
|
 投稿日時: 火 10月 13, 2020 8:32 pm 件名: |
|
 投稿日時: 火 10月 13, 2020 8:32 pm 件名: |
|
|
proplus wrote:
Good news, its actually an easy fix, unless you accidentally misalign and/or loosen the aperture blades.
At 2:52 in the video you'll see me rotating the silver ring within the aperture mechanism, it is underneath this ring that a tiny spring has detached on one end (its simple enough to figure out where the loose end goes). Once reattached, aperture works perfectly again.
To remove the metal ring, you first need to remove the aperture arm, and the unscrew the black covering via the 2 notches within the mechanism at 2:53 with a lens wrench. This covering presses down onto the aperture blade axis, so be careful from this point in not disturbing the aperture blades.
Its actually not a great design with how this spring is attached; the notches at both ends to where the spring attaches are not tapered or have any grip on them to firmly attached the spring ends. One good shake of this lens and the spring will detach and you'll get the common problem of the aperture being stuck wide open. |
|
| トップへ戻る |
|
 |
kiddo
 登録日: 2018年6月29日 投稿: 1630
|
 投稿日時: 水 10月 14, 2020 4:47 am 件名: |
|
 投稿日時: 水 10月 14, 2020 4:47 am 件名: |
|
|
kiddo wrote:
Hi, anyone could tell me what's the size of the aperture ring ball, as I've got a clickless lens. |
|
| トップへ戻る |
|
 |
Gonzoo
 登録日: 2010年3月29日 投稿: 231
|
 投稿日時: 木 10月 15, 2020 6:28 pm 件名: |
|
 投稿日時: 木 10月 15, 2020 6:28 pm 件名: |
|
|
Gonzoo wrote:
It's something in between 1.5mm and 2mm. IIRC Pentacon lenses feature a 1,8mm ball bearing diameter, you might try to salvage one from an inexpensive 50mm. See discussion here: http://forum.mflenses.com/lost-the-aperture-ball-bearing-how-to-found-out-its-size-t63678.html
| kiddo 氏の書き込み: |
| Hi, anyone could tell me what's the size of the aperture ring ball, as I've got a clickless lens. |
_________________ Canon 5d | Exa 500 | Pentacon Six + too much lenses  |
|
| トップへ戻る |
|
 |
|
|
|
このフォーラムでは新しいトピックを投稿できません このフォーラムではトピックに返信できません このフォーラムでは自分の投稿を編集できません このフォーラムでは自分の投稿を削除できません このフォーラムでは投票に参加できません
|