MFlenses - デジタル時代の新しさ
MFLenses 2026

マニュアルフォーカスレンズフォーラム

修理ノート、実際のテスト写真、画像豊富な詳細アーカイブスレッドから、ヴィンテージレンズの世界を探検してください。

修理ノート、実際のテスト写真、画像豊富な詳細アーカイブスレッドから、ヴィンテージレンズの世界を探検してください。
スポットライト

フォーラムトップページのおすすめパートナー掲載。

EMF focus confirm chip. MFA explained
前のトピックへ :: 次のトピックへ  


Reply

I cannot claim credit for all this information as it was gleaned from various sources, however I have attempted to simplify it and put all the information in one place, including adding a few bits that I have discovered personally.

All information below is confirmed to be correct using EMF programmable adaptor with a Canon 50D and various manual lenses.
Other cameras or Canon models may perform differently.


MFA with EMF AF Confirm Chip explained




For EMF chip MFA entry, you enter between 0-31, this converts to 5 digital bits.
5 digital bits represent 0-31 in base-10, but we need positive and negative values for MFA so
the chip interprets this as -16 to +15 for the same 5 bits.


As you can see in the table below, the following chart is the easiest way of understanding the

entry of the 0-31 chip values compared to the in-camera MFA values.The chart below is
for comparison of the direction of the two systems but the 2 scales do not correspond
numerically or proportionately.

(-16 to +15 using the 2's compliment 5 bit representation within the 0-31 values)


Effect:..................... (Max) Towards camera (Min)<Neutral>(Min) Away from camera (Max)

Camera MFA scale:...-20 ............-8 ..............-1 ..........0............+1 ............ +8 ............ +20

Enter value into chip: 16 .............24 ............31...........0..............1 .............. 8 ............. 15


THE EMF ADJUSTMENT GIVES A VERY COARSE CONTROL AND THE DIFFERENT DISTANCE BETWEEN
ANY 2 ADJACENT NUMBERS IS QUITE LARGE. The in-camera MFA adjustment is quite fine in comparison.

If you only have one EMF adaptor then it is easiest to leave the chip setting at it's default
and use only the in-camera MFA adjustment, however if you have more than one EMF adaptor then
the camera cannot differentiate between them so leave the in-camera setting at zero and program
each EMF adaptor for correct focus as necessary.

(Folllowing information amended and updated 10th Feb 2014)

The Canon cameras will achieve focus within the depth of field of the widest aperture of your
lens, this is not necessarily spot-on focus. The camera knows the widest aperture from the
information it gets electronically from the lens, or in this case from the EMF adaptor.
Obviously if you have a lens with a maximum aperture of f3.5 or f4.0 then the depth of field
can be quite wide and relying on focus confirmation will be prone to errors.
You will notice a marked difference in the focus acheived when you turn the focus ring from
one direction and then from the other.

If you program the aperture in the EMF adaptor as F1.1 irrespective of the actual lens aperture
then the autofocus within the camera will be much more precise when focussing because the
computed depth of field will be much narrower.I have found this to be much more accurate
especially with wide angle lenses of f2.8 or less.

Although this makes the EXIF information and the displayed aperture on the camera incorrect I
do not find this a problem as the important thing to me is getting the focus right. It makes
absolutely no difference to the exposure because the camera is reading the amount of light
coming through the lens and not relying on lens aperture information for metering.


最終編集: Ramon、月 2月 10, 2014 7:15 pm、計 1 回


Reply

Ramon,

Very useful info, thanks for posting,

Renato


Reply

Information in first post updated 10th Feb 2014.