David
 登録日: 2011年4月13日 投稿: 1869 所在地: Denver, Colorado
Expire: 2013-01-25
|
 投稿日時: 月 1月 28, 2013 6:29 am 件名: Calumet CC-401, Ilex Caltar 165mm 1:6.3, Lucky 100, D-76 1:1 |
|
 投稿日時: 月 1月 28, 2013 6:29 am 件名: Calumet CC-401, Ilex Caltar 165mm 1:6.3, Lucky 100, D-76 1:1 |
|
|
David wrote:
Today I did a bunch of experiments.
1- Could I walk with just one crutch?
2- Could I walk with one crutch and carry a 4X5 camera, tripod, and bag with lens and film backs at the same time?
3- Could I figure out how to use a 4X5 camera?
4- Would I like the results from 1:1 D-76 developing instead of simply using stock solution?
5- Instead of just agitating five seconds every minute, what would cycling the developer every third minute do? (I agitate minutes 1, 2, 4, 5, 7, 8, 10, and 11. I poured the developer into a graduated cylinder and then re-poured it into the tank at minutes 3, 6, 9, and 12, dumping it at 13:30.)
In short, all experiments seem to have resulted in various measures of success.
1- Yes
2- Yes
3- Mostly, the basics, anyway
4- Very much. I didn't enjoy standing there for 13 minutes over my ancient FR sheet film tank that can't be inverted, though. My leg is still in a dang cast!
5- Actually, I think this may be my new developing method. The results were fabulous.
My only barrier, besides being unable to walk for the last two months, to this experiment was the lack of a lens board. So on Saturday I hit Tap Plastics where they sell four-inch-by-four-inch samples. I picked up four at one dollar each. They also drilled the 33mm hole the Sekiosha shutter needs -- for free. So, yeah, my lens board was $1. It's matte on the back and high gloss on the front, which is easy for hand-etching lens data like infinity focus distance, maximum distance from the film with focus ability, and optimum apertures. I had to hand-sand off 1/16th of an inch from each side, but that was easy and left the edges nice and smooth. And the Caltar lens in Seikosha shutter on glossy black looks amazing.
I scanned the images in with five passes then stitched them in Photoshop. I used, per norm, my scanner's maximum optical resolution of 3,200 dpi. This yields images 11,940 X 14,985 pixel (178.9 megapixels) after cropping out the film border.
Some things to improve next time:
1- Don't get the camera's monorail in the picture.
2- Load the film correctly so that one of the negatives doesn't pop off and into the camera after the shot's taken while sliding the film cover back into place. Oops. I did that once.
3- Practice loading the film into the developing tub a few more times.
4- Get different films. Lucky is fine, but I want to try Acros, Velvia, and TMax on this.
5- Get a black cloth. Focusing in full sun was okay at f6.3, but the background kept reflecting on the image.
Some future experiments:
1- I found directions in an LF book I bought on how to develop for more even tones and reduced contrast. I forget the process, but it involves diluted developer and alternating one-minute developer and water rinses (reusing the same developer solution), or something to that effect. It's lengthy, but can do a lot of good for a negative that would otherwise have blown out shadows and highlights. I kinda tried that with this development, but without the water wash between.
2- Try some interesting subjects. This includes some architectural work, obviously.
3- See how the movements and aperture affect each other.
4- Build a K-mount adapter to fit onto the back of my CC-400 in lieu of the Graflock back. Why, you may ask. I ask why not! Actually, if I had a digital 645 back, it might be interesting to build a sliding adapter that would allow me to take like eight images with that back and then stitch them later. Hmmmmm.
Here are the image:
1
Notes: Infinity focus test 1. 1/4 second, f45 (not the furthest it will stop down.) Metered with a Sekonic Auto-Lumi
Thoughts: Hot potatoes is this lens sharp! I can see why this was going to replace the Commercial Ektar lenses.
2
Notes: Infinity focus test 2. 1/125th, f13. Metered using sunny 16 and guesswork.
Thoughts: Less sharp at f13 than I would have expected. Perhaps the lens' optimum sharpness is at smaller apertures than this. The white blob on the far left side is a bit of emulsion that wasn't developed. I also had about 1/2 inch of rise on the front but didn't realize it.
3
Notes: Not infinity test 1. 1/125th, f6.3. Metered with the Sekonic Auto-Lumi. Front lift about 1/3 inch. Rear tilt about 12 degrees forward.
Thoughts: I am going to love learning how movements work. I'm starting to see, even in these few tests, why movements are such a powerful photographic tool. Someone needs to make a 4X5 CCD. Just sayin'.
4
Notes: Not infinity test 2. 1/125th, f6.3. No front rise and no rear tilt.
Thoughts: I may have the notes on this and image five reversed.
5
Notes: Not infinity test 3. 1/125th, f6.3. No front lift, about 15 degrees rear tilt backward.
Thoughts: I love this lens. I can't wait to try some films with better contrast profiles. I can't wait to try some slide film. _________________ http://www.youtube.com/user/hancockDavidM |
|