| 前のトピックへ :: 次のトピックへ |
| 作成者 |
メッセージ |
Väsen
登録日: 2011年9月6日 投稿: 38
|
 投稿日時: 木 10月 18, 2012 8:08 pm 件名: CJZ 135 f/3,5 re-assembly- aperture rod and its holder issue |
|
 投稿日時: 木 10月 18, 2012 8:08 pm 件名: CJZ 135 f/3,5 re-assembly- aperture rod and its holder issue |
|
|
Väsen wrote:
Hi.
I've taken the 135 MC apart once before and reassembled it without any real issues, via http://www.andrew.brown.dsl.pipex.com/articles/czj135svc/ . I never understood what he means by "With the focussing ring set on infinity you need to turn the focussing barrel(3) all the way inwards (infinity is when the lens is at its shortest) so that it comes right off its thread." since there's a break in the thread(360 degrees) near its end so if you try to screw it 'right off its thread' it instead gets severely stuck; but by something like blind luck it got screwed in so that infinity was lined up with the infinity mark last time.
The primary issue this second time around (and don't use Tri-Flow grease for focusing helicoids) is that I can't get 'holder' in the top part, for the aperture rod, to align with the rod. The lever for A and M modes always works when I put the top on, but the little rod simply will not stay in the holder. Nothing looks bent. I'm seriously considering leaving it in A mode and truncating the peg so that the lens stays wide open, since I almost always use it like that. It just seems like a shame because the rod should stay in the holder when I snap the top part on.
Has anyone any hint? |
|
| トップへ戻る |
|
 |
Väsen
登録日: 2011年9月6日 投稿: 38
|
 投稿日時: 土 10月 20, 2012 11:31 am 件名: |
|
 投稿日時: 土 10月 20, 2012 11:31 am 件名: |
|
|
Väsen wrote:
I suppose not. Oh well, since this lens was always used wide open when it was used, I removed the mode selector lever of the top part, inlcuding the mode pin that sticks out(I unscrewed it, the operation can theoretically be reversed).
With nothing to manipulate the mode selector lever of the body, the aperture defaults to wide open and the two switches on the top do nothing.
Shall receive a Super Tak 135 f/3,5 early next week and it'll be interesting to see the differences (at f/3.5). People say the Super Tak can have nervous bokeh, but so can this aus Jena, the thing I love it for is its sharpness wide open. |
|
| トップへ戻る |
|
 |
fermy
 登録日: 2012年2月17日 投稿: 1974
|
 投稿日時: 日 10月 21, 2012 2:33 am 件名: |
|
 投稿日時: 日 10月 21, 2012 2:33 am 件名: |
|
|
fermy wrote:
I've never disassembled this particular lens, however, I've disassembled other CZJ lenses. IMHO the instructions at this point are simply wrong. It's very difficult (but sometimes you get lucky) to mate helicoids from the rear, where the threads end rather than start. This is the problem you are having.
There should be a way to unscrew the focusing barrel from the front of the lens and consequently screw it back in from the front. That way the threads should mate easily and after some trial and error you will find the correct starting position and line up everything correctly. _________________ Many lenses and some film bodies for sale here: http://forum.mflenses.com/canon-fd-minolta-md-c-mounts-m42-pentax-and-more-t50465.html
Flickr http://www.flickr.com/photos/96060788@N06/ |
|
| トップへ戻る |
|
 |
Väsen
登録日: 2011年9月6日 投稿: 38
|
 投稿日時: 月 10月 22, 2012 12:32 pm 件名: |
|
 投稿日時: 月 10月 22, 2012 12:32 pm 件名: |
|
|
Väsen wrote:
Hi.
Indeed, there is a way to mate the barrel with the helicoid from the top and get proper focus. In some old post someone suggested there was were marks on the helicoid and the barrel to indicate where the threads should meet, however I failed to find any such mark. There is a distinct 'V' on the focus ring however, but as there's nothing on the helicoid it doesn't help much.
The issue I was having here was with the aperture rod and the top piece however : ) |
|
| トップへ戻る |
|
 |
fermy
 登録日: 2012年2月17日 投稿: 1974
|
 投稿日時: 水 10月 24, 2012 4:37 am 件名: |
|
 投稿日時: 水 10月 24, 2012 4:37 am 件名: |
|
|
fermy wrote:
What I am saying is that you should try mating the helicoid from the top until the top piece and rod line up properly.
The reason why I suggest doing it from the top is that it's 10x faster than from the bottom, so trial and error approach is feasible. _________________ Many lenses and some film bodies for sale here: http://forum.mflenses.com/canon-fd-minolta-md-c-mounts-m42-pentax-and-more-t50465.html
Flickr http://www.flickr.com/photos/96060788@N06/ |
|
| トップへ戻る |
|
 |
Väsen
登録日: 2011年9月6日 投稿: 38
|
 投稿日時: 水 10月 24, 2012 4:01 pm 件名: |
|
 投稿日時: 水 10月 24, 2012 4:01 pm 件名: |
|
|
Väsen wrote:
I'm afraid I don't understand. The main body (helicoid) mates with the focussing barrel. You can do that from the top or try to do it from the bottom.
The top part however, this : http://www.andrew.brown.dsl.pipex.com/articles/czj135svc/images/2.jpg is simply snapped onto the helicoid , preferrably with the aperture rod 'fastened' to its holder and the mode lever selection rod over the mode lever. There is no 'top' or 'bottom' part of this that I can conceive of. |
|
| トップへ戻る |
|
 |
fermy
 登録日: 2012年2月17日 投稿: 1974
|
 投稿日時: 水 10月 24, 2012 5:15 pm 件名: |
|
 投稿日時: 水 10月 24, 2012 5:15 pm 件名: |
|
|
fermy wrote:
The part you are showing is screwed onto the rest of the lens. So if something does not line up properly, chances are that the rest of the lens has been assembled incorrectly. _________________ Many lenses and some film bodies for sale here: http://forum.mflenses.com/canon-fd-minolta-md-c-mounts-m42-pentax-and-more-t50465.html
Flickr http://www.flickr.com/photos/96060788@N06/ |
|
| トップへ戻る |
|
 |
Väsen
登録日: 2011年9月6日 投稿: 38
|
 投稿日時: 木 10月 25, 2012 9:12 am 件名: |
|
 投稿日時: 木 10月 25, 2012 9:12 am 件名: |
|
|
Väsen wrote:
No, it doesn't screw on, it's just put on. It isn't a question of anything to do with the helicoid threads or anything else, it's merely a question of being deft-of-hand enough to get the holder in the top part to 'mate' with the aperture lever properly. |
|
| トップへ戻る |
|
 |
Gonzoo
 登録日: 2010年3月29日 投稿: 231
|
 投稿日時: 火 11月 06, 2012 10:16 am 件名: |
|
 投稿日時: 火 11月 06, 2012 10:16 am 件名: |
|
|
Gonzoo wrote:
Don't know if this helps, but I fixed a CZJ MC 135mm a few weeks ago using these instructions:
https://picasaweb.google.com/111466649819981314803/CZJ135Repair
https://secure.flickr.com/photos/34694152@N00/746619911/in/set-72157594512669706/
offtopic: Fermy, can you provide me with some images of the two springs near the apperture? _________________ Canon 5d | Exa 500 | Pentacon Six + too much lenses  |
|
| トップへ戻る |
|
 |
philslizzy
 登録日: 2012年8月7日 投稿: 4753 所在地: Cheshire, England
|
 投稿日時: 金 11月 23, 2012 11:50 pm 件名: |
|
 投稿日時: 金 11月 23, 2012 11:50 pm 件名: |
|
|
philslizzy wrote:
| Väsen 氏の書き込み: |
| No, it doesn't screw on, it's just put on. It isn't a question of anything to do with the helicoid threads or anything else, it's merely a question of being deft-of-hand enough to get the holder in the top part to 'mate' with the aperture lever properly. |
On the part that comes off when you've got the three screws off is the long flat strip that controls the aperture linkage. I suggest you put the aperture on the lens in the f22 position and move the long flat strip also to the f22 position. The long strip slides into a channel on the aperture linkage on the lens side, slip that in the end first, about a couple of millimetres will do, then concentrate on the linkage on the other side, I assume you know how they mate together, jiggle them about lining up the v's, theyre both roughly v shape, they will just pop into place. I takes me a minute or so of jiggling as they've got to be exactly lined up.
I cleaned the fungus off my lens but the aperture is well sticky. I've tried lighter fluid and alcohol to no avail. I'm not taking the whole thing apart! |
|
| トップへ戻る |
|
 |
|
|
|
このフォーラムでは新しいトピックを投稿できません このフォーラムではトピックに返信できません このフォーラムでは自分の投稿を編集できません このフォーラムでは自分の投稿を削除できません このフォーラムでは投票に参加できません
|