MFlenses - デジタル時代の新しさ
MFLenses 2026

マニュアルフォーカスレンズフォーラム

修理ノート、実際のテスト写真、画像豊富な詳細アーカイブスレッドから、ヴィンテージレンズの世界を探検してください。

修理ノート、実際のテスト写真、画像豊富な詳細アーカイブスレッドから、ヴィンテージレンズの世界を探検してください。
スポットライト

フォーラムトップページのおすすめパートナー掲載。

Contax 645 adapter to EOS (SOLVED)
前のトピックへ :: 次のトピックへ  


Reply

I've just received a lens which I believe has a Contax 645 mount, so what I need is an adapter to enable me to use it on my Canon 7D. I've searched online but can only find an adapter which has it's own aperture assembly built in. I don't need that because this lens is all manual (plus they want £175 Shocked ).
Has anyone here ever bought what I'm looking for?


最終編集: SonicScot、火 7月 10, 2012 5:05 pm、計 1 回


Reply

You would need an electronic adapter that can control the lens aperture using Canon EF electronics
Such a thing would be greatly expensive and would probably require a hardware conversion of the lens in it's electronic parts
(lens which would then lose all it's value for resale)
so the built in aperture in the adapter is the most cost-effective and logical way.

Having that said, I would rather spend 200 Euros on a native 135 format lens, than on an adapter for a medium format lens.
Even when excellent, medium format lenses have a hard time competing with native 135 format lenses.


Reply

I'm not sure I understand the need for any electronic connection between lens and camera, my other lenses don't need it. Can you tell me what I'm missing here?
The lens has a manual aperture ring, just like my other lenses.
I'm confused. Confused


Reply

Maybe I'm wrong about the mount, perhaps someone will identify it from this picture.



This is why I'm confused by the need for electronic connection, I can't see any contacts on the mount. (of course I could be wrong)


Reply

Orio is thinking at the Contax lenses for Contax 645 because you didn`t specify the lens, brand, etc.
That`s why his answer.
Obviously that is not a Contax. I don`t recognize the mount.


Reply

Himself 氏の書き込み:
Orio is thinking at the Contax lenses for Contax 645 because you didn`t specify the lens, brand, etc.
That`s why his answer.
Obviously that is not a Contax. I don`t recognize the mount.

Ah, right. My fault, I should have been more specific. It's a Hartblei Super-Rotator 45mm f3.5 TS-PC as seen here http://www.hartblei.com/lenses/lens_45mm.htm
According to that site it comes in four mounts: Pentacon Six, Mamiya 645, Contax 645 and Pentax 645. Not knowing what any of those look like I don't know what mine is. The inside diameter of the mount is 66mm, that's really all I know.
I have a couple more photos, which might help.




Reply

Now that you say it, it looks like a P6 mount to me eyes.
I`m looking forward to seeing some pictures with that lens.
The PC functions mainly.


Reply

Himself 氏の書き込み:
Now that you say it, it looks like a P6 mount to me eyes.

That would be fantastic because it's easy to get adapters to Canon. The guy I got it from was unsure but thought it was Contax 645.


Reply

How much was it?
I suspect 2-300$ .


Reply

The Contax 645 lenses have the aperture ring, but the iris can only be operated electronically.
Hopefully your lens could be a Pentacon 6 mount, in that case adaptation is easy.


Reply

Himself 氏の書き込み:
How much was it?
I suspect 2-300$ .

You wouldn't believe me if I told you Wink but it was a lot less Razz


Reply

Orio 氏の書き込み:
The Contax 645 lenses have the aperture ring, but the iris can only be operated electronically.
Hopefully your lens could be a Pentacon 6 mount, in that case adaptation is easy.

The aperture ring is opens and closes the blades, just like all my other mf lenses. I can't see where electric connection could be made. Their website recommends the Pentacon Six mount as a 'universal mount' because adapters are easy to use. I wonder, if this is Contax 64, if I can change the mount myself,..?


Reply

Once again, Orio is talking about Contax 645 lenses not third party lenses with Contax 645 mount.


Reply

SonicScot 氏の書き込み:
Himself 氏の書き込み:
How much was it?
I suspect 2-300$ .

You wouldn't believe me if I told you Wink but it was a lot less Razz

Actually no cash changed hands, I fitted a new front door and a kitchen window in exchange for it. The work took about 90 minutes.
On ebay these cost a lot of money ここをクリックしてeBayで見る Shocked


Reply

Himself 氏の書き込み:
Once again, Orio is talking about Contax 645 lenses not third party lenses with Contax 645 mount.

Ok Smile I said I was confused Laughing


最終編集: SonicScot、土 7月 07, 2012 5:17 pm、計 1 回


Reply

Himself 氏の書き込み:
Once again, Orio is talking about Contax 645 lenses not third party lenses with Contax 645 mount.


Yes.
Third party lenses (if they exist) if lacking the electronics should be operated manually
(and the camera of course used in stop down manual mode).


Reply

From what I can find, Pentacon Six lenses have three flanges (?) around the mount, my lens has four. Contax 645 has four.


Reply

I do install windows and doors.
A small window could take 60-80 min, a simple front door + lockers, no side lights, up to 3 hours.


Reply

Himself 氏の書き込み:
I do install windows and doors.
A small window could take 60-80 min, a simple front door + lockers, no side lights, up to 3 hours.

The door was prepared with locks and hinges, so it took ten minutes to hang and adjust. The poor joiner who was doing the work broke his leg and arm skiing on holiday.
The window was made to measure, the old one had never been fixed in place Surprised so it practically fell out. easy and quick job. Very Happy


Reply

Hmm, so the door was actually only the slab. Take out old slab put the new one.
As for the lens, if it`s the real Hartbley made in Germany with Zeiss optics, you had the heck of a deal.


Reply

Himself 氏の書き込み:
Hmm, so the door was actually only the slab. Take out old slab put the new one.
As for the lens, if it`s the real Hartbley made in Germany with Zeiss optics, you had the heck of a deal.

The unlucky joiner replaced the rear door and five other windows before he went on holiday, he planned to finish off when he came back.
The house owner is a friend of a friend, I was recommended to finish the job. He knew me from my photography and offered a deal, I tried to look calm when he pulled this lens out and offered it for the work. He doesn't do photography but was given a case full of gear last year as a bonus at his work. He works on oil rigs out east and often comes home with bonus electronics. Very Happy


Reply

I emailed Hartblei themselves to ask if they had some kind of adapter I could use, or even if I could change the mount to Pentacon Six myself. They're reply, "The Contax 645 / Canon EOS adapter is not possible. And the lens has fixed mount. Sorry, but we are not able to help you."
Now, personally, I see that as a challenge. Twisted Evil Maybe I can find a knackered Pentacon Six lens that I can steal the mount from and swap them over.... Razz


Reply

SonicScot 氏の書き込み:
They're reply, "The Contax 645 / Canon EOS adapter is not possible.


This is a stupid reply. The adapter is possible, register distance allows for it.
It may be awkward (for the built in iris), expensive (for the 200 Euros), not worth it, but it certainly is possible.


Reply

Orio 氏の書き込み:
SonicScot 氏の書き込み:
They're reply, "The Contax 645 / Canon EOS adapter is not possible.


This is a stupid reply. The adapter is possible, register distance allows for it.
It may be awkward (for the built in iris), expensive (for the 200 Euros), not worth it, but it certainly is possible.

That's what I thought too so I emailed them again to ask about changing the mount to a Pentacon Six one, their reply was "The replacement is possible by technicians only. But this lens is no longer available for sale and we don’t have appropriate mount."
I bet that somewhere they will have the 'appropriate mount' lying in a storeroom gathering dust, they just don't seem inclined to help.
'Technicians only' ha! There's three small screws holding the mount in place, I can't see how it takes a 'technician' to remove three screws. Confused
So I've now emailed Zoerk, who make adapters, for help and also Kipon who make the very expensive adapter with aperture assembly. I've explained how I don't require the aperture blades and asked to buy a basic 'shell' of the adapter. My email was very polite and extremely complimentary of their design and build quality Razz perhaps flattery will get me what I want. Laughing


Reply

I came across an old blog entry by a photographer in England, in which he described the exact same problem I've been having finding a way to connect this obscure lens to my Canon. The blog was from back in 2007 and it named the engineering firm which eventually solved his problem.
Today I contacted the same firm, in fact the same engineer, and despite the fact that they haven't kept a record of the previous job (likely lost the drawings when there was a merger), they are going to convert my lens to fit my 7D! Razz
This engineering company have a lot of work on so it isn't easy to fit in these one-off jobs, it's amazing that they'll do the work at all. I've posted the lens to this company today and probably won't see it again for 6 weeks but I don't mind. The cost of the work is half the price of the Kipon adapter I found on ebay. Twisted Evil
If anyone else has an adapter issue that they can't seem to fix, get in touch with these guys.
http://www.srb-griturn.com/index.asp

Edit; forgot to mention, I've heard nothing from Zoerk since I emailed them.