| 前のトピックへ :: 次のトピックへ |
| 作成者 |
メッセージ |
Anu
 登録日: 2009年4月14日 投稿: 879
|
 投稿日時: 木 10月 21, 2010 8:37 pm 件名: I need help to fix aperture of Pancolar 80/1.8 |
|
 投稿日時: 木 10月 21, 2010 8:37 pm 件名: I need help to fix aperture of Pancolar 80/1.8 |
|
|
Anu wrote:
As usualy, this happens when I fix a lens - thse are left-overs after I reassembled the lens:
After several hours of failed attempts I just gave up and rebuilt the lens witout these items. I just can't get the blades in their place. And even though I took photos while tearing the lens apart, I am not at all sure how the blades should be arranged any more. I am just too stipid for stuff like this and I would really like to have one or two of extra hands coming from my torso.
This is a quick and dirty classing shoot-the-bill-test - it's a bit off center crop, not even sure if it is in focus, don't care at this hour - also, it's ISO 4.000+, so excuse the noise (and it's negative influence on the resolving ability).
I am sure I need not mention what the lens is - it cost me about 160 euros or so. |
|
| トップへ戻る |
|
 |
martyn_bannister
 登録日: 2010年5月23日 投稿: 1151
|
 投稿日時: 土 10月 23, 2010 11:22 am 件名: |
|
 投稿日時: 土 10月 23, 2010 11:22 am 件名: |
|
|
martyn_bannister wrote:
Ah yes, the "I need four hands with 7 fingers each" feeling. I know it well
Alternating with the "I need one hand with twenty fingers" feeling
I am not familiar with this particular lens but, once everything has been cleaned.....
Of the two rings on the left of your picture, I think you start with the large one then lay the other ring inside it. Each aperture blade should have two pins, one of which will engage in a slot/indentation in the large ring, the other in a slot/indentation in the smaller ring. Lay one blade on the rings with the pins in the slots. By turning one ring in relation to the other, the aperture blade should "close down" in the manner to which we are accustomed.
Once you can see how a single blade works in relation to the rings, it is "merely" a question of added successive blades, each one on top of the previous. Of course, when you get to the last one, it has to be sort of inserted between the first one you placed and the last one you placed. This is tricky
At this stage, turning the rings in relation to each other should result in a fully functioning aperture. Be careful, because at this stage (or any other ) success can be torn from your grasp by all the blades becoming dislodged (accompanied by much cursing)
Either the large ring on the right of your picture, or the lens body, itself will keep the blade in place once everything is assembled.
Of course, as you have shown, it works very well with no aperture at all  |
|
| トップへ戻る |
|
 |
Anu
 登録日: 2009年4月14日 投稿: 879
|
 投稿日時: 土 10月 23, 2010 3:55 pm 件名: |
|
 投稿日時: 土 10月 23, 2010 3:55 pm 件名: |
|
|
Anu wrote:
| martyn_bannister 氏の書き込み: |
Ah yes, the "I need four hands with 7 fingers each" feeling. I know it well
Alternating with the "I need one hand with twenty fingers" feeling
I am not familiar with this particular lens but, once everything has been cleaned.....
Of the two rings on the left of your picture, I think you start with the large one then lay the other ring inside it. Each aperture blade should have two pins, one of which will engage in a slot/indentation in the large ring, the other in a slot/indentation in the smaller ring. Lay one blade on the rings with the pins in the slots. By turning one ring in relation to the other, the aperture blade should "close down" in the manner to which we are accustomed.
Once you can see how a single blade works in relation to the rings, it is "merely" a question of added successive blades, each one on top of the previous. Of course, when you get to the last one, it has to be sort of inserted between the first one you placed and the last one you placed. This is tricky
At this stage, turning the rings in relation to each other should result in a fully functioning aperture. Be careful, because at this stage (or any other ) success can be torn from your grasp by all the blades becoming dislodged (accompanied by much cursing)
Either the large ring on the right of your picture, or the lens body, itself will keep the blade in place once everything is assembled.
Of course, as you have shown, it works very well with no aperture at all  |
While I appreciate the help, it big problem not so much putting the blades into the two-ring-construction (takes two hours of careful play with inadequate tools and hands of mine ), but managing to get this loose construction somehow into the lens in one piece. The 180/2.8 and 300/4 aperture mechanism was a bit simpler in that there were no two separate round rings torturing the service person, though somehow the 180 is still lacking the aperture mechanismm
I did take tons of shots when I tore the lens apart, but mostly the wrong pictures Even though the two rings and the blades are all now nicely connected, but I am not at all sure the two rings are positioned properly relative to each other - it is possible one (though probably not the other) should be flipped upside down. Anyhow, it seems as it there is nothing really preventing these construction from collapsing if I just dare to try to life it up, though turning it all upside down might help, at least if the blades just manage to hold themselves together.
I will probably try to fix the darn thng next week once I buy better tools and/or get even more help and instructions. |
|
| トップへ戻る |
|
 |
martyn_bannister
 登録日: 2010年5月23日 投稿: 1151
|
 投稿日時: 土 10月 23, 2010 4:07 pm 件名: |
|
 投稿日時: 土 10月 23, 2010 4:07 pm 件名: |
|
|
martyn_bannister wrote:
Perhaps blades have to be assembled inside lens? I had one like that. Long tweezers and a lot of patience required
"If it came apart, one must be able to put it back together"
If you get sick of it, just send it to me. I love a puzzle  |
|
| トップへ戻る |
|
 |
Anu
 登録日: 2009年4月14日 投稿: 879
|
|
| トップへ戻る |
|
 |
sadness
登録日: 2010年8月16日 投稿: 49 所在地: Constanta, Romania
|
 投稿日時: 水 10月 27, 2010 8:45 am 件名: |
|
 投稿日時: 水 10月 27, 2010 8:45 am 件名: |
|
|
sadness wrote:
It is similar to the Pancolar 50mm f1.8 I cleaned just recently, yesterday, or so it seems.
the two rings on the left of your picture are assembled first with little one inside.
The extensions of small one in the place of the inside cut of the other, then assemble the blades.
Blades are placed in clockwise order, the last one comes over previous and beneath first.
In 50mm there was another ring placed on top then came the rightmost ring from your picture. and after that a screw ring.
I have pictures with all parts if you want I can send or post here.
Good luck.
Hope it helps. _________________ My site motorai.ro as motorcycle addict, I post on the blog of the site.
casti moto piese moto accesorii moto echipamente moto |
|
| トップへ戻る |
|
 |
Anu
 登録日: 2009年4月14日 投稿: 879
|
 投稿日時: 水 10月 27, 2010 3:15 pm 件名: |
|
 投稿日時: 水 10月 27, 2010 3:15 pm 件名: |
|
|
Anu wrote:
| sadness 氏の書き込み: |
It is similar to the Pancolar 50mm f1.8 I cleaned just recently, yesterday, or so it seems.
the two rings on the left of your picture are assembled first with little one inside.
The extensions of small one in the place of the inside cut of the other, then assemble the blades.
Blades are placed in clockwise order, the last one comes over previous and beneath first.
In 50mm there was another ring placed on top then came the rightmost ring from your picture. and after that a screw ring.
I have pictures with all parts if you want I can send or post here.
Good luck.
Hope it helps. |
Thank you!
I would appreciate the imagery much, but maybe it would better if they'd start up a new thread so that people seeking help for 50/1.8 might find it easier to find it by searching.
Pictures are always worth more than a few words - even in photography forum  |
|
| トップへ戻る |
|
 |
|
|
|
このフォーラムでは新しいトピックを投稿できません このフォーラムではトピックに返信できません このフォーラムでは自分の投稿を編集できません このフォーラムでは自分の投稿を削除できません このフォーラムでは投票に参加できません
|